OPTIONS OVERVIEW
                                               For The 3200 Electrical Test Equipment Calibrator


HIGH ACCURACY RESISTANCE OPTION
Higher Accuracy - approximately 3 times better for the insulation resistance and continuity resistance.
Recommended for calibration laboratories which may wish to use the 3200 for other uses and also
provides the accuracy for more accurate insulation testers in the future
- NOT RETRO-FITTABLE

10GOHM OPTION
                                                             Transformers
Extends the resistance range for the standard 2G Ohms to 10G Ohms to cover calibration of insulation
testers with higher ranges - RETRO-FITTABLE (requires return to factory for fitting)

AUTO LOOP OPTION
                                                     A48062667A000G
Auto loop measures the supplied loop impedance and automatically adds this to the internal resistance
value, enabling the value displayed by the 3200 to be directly used for calibration of loop testers. Without
this option the loop value (at the test socket) must be measured and entered manually into the calibrator.

The auto loop option is particularly useful when the supply loop impedance is unstable or the socket /
location of the calibrator changes (e.g. on site work) - NOT RETRO-FITTABLE.

EXTERNAL RESISTOR OPTION
Allows the user to add two custom resistance values for use with the LOOP and PAT Earth Bond
resistance modes. These additional resistors supplied by the user are connected to two sets of terminals
on the rear panel - RETRO-FITTABLE.
 Input                                            Environmental
Voltage                230 VAC                               Operating Temperature   0 to 40 deg. C with no derating
Line Frequency         50 Hz                                 Storage Temperature     -30 to +85 deg. C
Configuration          Wall Mount; no Ground                 Relative Humidity       5% to 95% non-condensing
EXTERNAL 5kV ADAPTOR                                         Altitude                0-10,000 feet
 Electrical                                                  Cooling                 Convectional - non vented case
Provides a low cost solution for calibrating 5kV insulation testers (Megger BM11 etc.).
Topology             Step Down AC/AC Transformer           Mechanical
Dielectric Withstand
Testers must have Meets the requirements and be able to supply at least 5mA output current.
                     a guard terminal of safety
                     agencies.                            Case and Dimensions 3.2 L x 2.2 W x 1.9 H (in.) 81 L x 55 W x
The adaptor multiplies the resistance output from the 3200 by 10, therefore being able
Protection           Current, Thermal, or Energy Limiting                     48 H (mm)
to simulate up to 1T Ohm if the 10G option is fitted Case Material
                                                          to the 3200.        Black 94 V1 Polycarbonate
 Safety Approvals                                         Weight
Please note the adaptor does not measure the 5kV test voltage.                18 ounces; 520 grams
                                                          Configuration       Wall Mount; no Ground
TUV EN60950
PAT FLASH ADAPTOR

                         Measures the flash test voltage and current generated by PATs when performing
                         Class 1 and 2 (1.5kV / 3 kV) FLASH tests.
                         Two measurement modes are available ­
                         Zero Load      : AC Voltage only is displayed
                         Under Load : AC Voltage and current (into nominal 1mA load) is displayed

HI-POT / FLASH / BREAKDOWN TESTER ADAPTOR


                   Test HI-Pot / Flash / Breakdown testers using this external adaptor.
                   Measure AC / DC Voltage to 12 kV (3kV & 2kV Ranges) and Currents from 200uA to
                   20mA @ 1 kV into 9 selectable resistance loads (3 current ranges).
                   Incorporates LED range indication.




OPTIONS OVERVIEW
For The 3200 Electrical Test Equipment Calibrator : V1.00
           CompuMess Elektronik GmbH · Lise-Meitner-Str.1 · 85716 Unterschleissheim
                 Tel 089-321501-0 · Fax 089-321501-11 · www.compumess.de · www.netzteile.de