MPO-200S Series
Single Output, 200W
Miniature, Open Frame
AC/DC Power Supplies
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features: Input
· 200W Output Power Parameter Conditions Min. Typ. Max. Units
· PFC to EN 61000-3-2,3 "D" Universal
90 264 VAC
Input Voltage Range
127 373 VDC
· Universal 90-264 AC Input
Input Frequency 47 63 Hz
· EN 60950 Approved (UL) Input Filter Meets EN 55022 Class B; FCC Class B
· Miniature 3 x 5 In Package Input Current See Model Selection Guide
· Meets EN 55022 B Cold Start, 115 VAC 36.0
Inrush Current A Pk
· Efficiency To 92% Cold Start, 230 VAC 100.0
Safety Ground Leakage Current 264 VAC 3.5 mA
· >110 kHour MTBF
Output
Parameter Conditions Min. Typ. Max. Units
Output Voltage/Current See Model Selection Guide
Output Voltage Tolerance See Note 1 ±1.0 %
Line Regulation Vin = Min to Max ±0.5 %
Load Regulation Iout = 10% to 100% ±1.0 %
Ripple & Noise (20 MHz) See Note 2 ±1.0 %
Hold-Up Time See Note 3 10 mSec
Temperature Coefficient ±0.05 %/°C
Short Circuit Protection Continuous (Autorecovery)
Over Voltage Protection See Note 3 130 %
General
Parameter Conditions Min. Typ. Max. Units
Isolation Voltage Input to Output 4,000 VAC
Isolation Resistance 500 VDC 1,000 M
Isolation Capacitance 5,845 pF
EMI/RFI Conducted EN 55022; EN 61000-3-2, -3
Electrostatic Discharge (ESD) IEC/EN 61000-4-2, -6, -8, -11
RF Field Susceptibility IEC/EN 61000-4-3
EMC Compliance
Electrical Fast Transients/Bursts On Mains IEC/EN 61000-4-4
Surge IEC/EN 61000-4-5
Switching Frequency Fixed 90 kHz
Environmental
Parameter Conditions Min. Typ. Max. Units
MicroPower Direct Operating Temperature Range -20
Ambient +25 +80 °C
292 Page Street
Storage Temperature Range -20 +85 °C
Suite D
Stoughton, MA 02072 Cooling See Derating Curve
USA Humidity RH, Non-condensing 93 %
Physical
T: (781) 344-8226 Size 5.00 x 3.00 x 1.44 Inches (127.00 x 76.20 x 34.00 mm)
F: (781) 344-8481
Weight 14.10 Oz (0.400 kg)
E: sales@micropowerdirect.com
W: www.micropowerdirect.com Reliability Specifications
Parameter Conditions Min. Typ. Max. Units
MTBF MIL HDBK 217F, 25°C, Gnd Benign 110 kHours
Safety Standards UL 60950, EN 60950
Vibration Sinusoidal 50~500 Hz, 3.0 Grms, Period of 30 min each along X, Y & Z Axis
www.micropowerdirect.com
CompuMess Elektronik GmbH · Lise-Meitner-Str. 4 · D-85716 Unterschleißheim
Telefon (089) 32 15 01 - 0 · Telefax (089) 32 15 01 - 11
info@compumess.de · www.compumess.de · www.netzteile.de
CompuMess Elektronik GmbH · Lise-Meitner-Str. 4 · D-85716 Unterschleißheim
Telefon (089) 32 15 01 - 0 · Telefax (089) 32 15 01 - 11
Model Selection Guide www.micropowerdirect.com
info@compumess.de · www.compumess.de · www.netzteile.de
Input Output Output Power Max
Model Current (A) Current (A) (Max. W) Output Efficiency
Number Voltage Capacitance (%, Typ)
(VDC) Maximum Maximum
115 VAC 230 VAC % Min. With 19 CFM Convection (µF)
(With 19 CFM) (Convection)
MPO-200S-12 3.0 1.5 12.0 16.67 12.50 0.00 200 150 6,000 89
MPO-200S-24 3.0 1.5 24.0 8.34 6.25 0.00 200 150 6,000 90
MPO-200S-36 3.0 1.5 36.0 5.56 4.17 0.00 200 150 4,450 91
MPO-200S-48 3.0 1.5 48.0 4.17 3.13 0.00 200 150 3,700 92
Notes:
1. Output voltage tolerance is measured at nominal
Derating Curve
input and 60% load.
2. Output ripple is measured at 20 MHz bandwidth
using 0.1 µF and 10 µF capacitors connected in
parallel as close to the power supply terminals as
possible.
3. Hold-up time is typical for 115 VAC and 230 VAC Connections
inputs. Input Connector (CN1):
4. These units will operate at no load without · TKP PVH1-3N2 or equivalent (one pin removed)
damage. For most applications however, MPD · Mating Housing: JST VHR-3N or equivalent
recommends that a minimum load always be · Mating Terminal: SVH-21T-PH1 or equivalent
used. Contact the factory for more information.
5. The remote sense outputs may be used to com- Pin Function
pensates for up to a 0.5V line drop. 1 AC-Line
6. The fan drive provides 12VDC @ 300 mA. 2 Removed
7. Each unit includes an input fuse (250V/5A). Since
3 AC-Neutral
this fuse is not field replaceable, it is recom-
mended that an external fuse of the same size Safety Ground:
be used on the input of the power supply for The unit should be mounted using metal standoffs. The
protection. input side mounting hole marked "FG" provides the safety
earth ground for the unit. This point should be connected to
the system earth ground via a metal spacer or a cable. This
connection should be locked to prevent possible loosening.
Mechanical Dimensions Connecting the output side mounting holes to earth ground
improves EMI (this connection will also put the rear heatsink
at ground potential).
Output Connector (CN2):
· TKP PVH1-08 or equivalent
· Mating Housing: JST-VHR-8N or equivalent
· Mating Terminal: SVH-21T-PH1 or equivalent
Pin Function Pin Function
1 +VOUT 5 -VOUT
2 +VOUT 6 -VOUT
3 +VOUT 7 -VOUT
4 +VOUT 8 -VOUT
Remote Sense Connector (CN3):
· LCU P205DG-02 or equivalent
· Mating Housing: Molex 5051-02 or equivalent
· Mating Terminal: Molex 5159 or equivalent
Pin Function
1 +Rs
2 -Rs
Fan Drive Connector (CN4):
· LCU P205DG-02 or equivalent
· Mating Housing: Molex 5051-02 or equivalent
· Mating Terminal: Molex 5159 or equivalent
Pin Function
1 +Fan Out
2 -Fan Out
See note 5 above
MicroPower Direct Notes:
· All dimensions are typical in inches (mm)
· Tolerance x.xx = ±0.02 (±0.50)
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 · CompuMess ElektronikFAX: (781) 344-8481 · E-Mail:· D-85716 Unterschleißheim
TEL: (781) 344-8226 · GmbH · Lise-Meitner-Str. 4 sales@micropowerdirect.com
Telefon (089) 32 15 01 - 0 · Telefax (089) 32 15 01 - 11
info@compumess.de · www.compumess.de · www.netzteile.de