MicroPower
Direct
Compact MiniDIP, 2W Key Features
Single & Dual Output Miniature DIP Package 1.0 kVDC Isolation
DC/DC Converters 2W Output Power Single & Dual Outputs
G200 Series 3.6 MH MTBF Low Cost
Electrical Specifications
Specifications typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter Conditions Min. Typ. Max. Units
5 VDC Input 4.5 5.0 5.5
12 VDC Input 10.8 12.0 13.2
Input Voltage Range VDC
24 VDC Input 21.6 24.0 26.4
48 VDC Input 43.2 48.0 52.8
Input Filter Internal Capacitor
Reverse Polarity Input Current 0.3 A
Output
Parameter Conditions Min.
Typ. Max. Units
Output Voltage Accuracy !1.0 !3.0 %
Output Voltage Balance Dual Output , Balanced Loads !0.1 !1.0 %
Line Regulation For Vin Change of 1% !1.2 !1.5 %
Load Regulation See Model Selection Guide
Ripple & Noise (20 MHz) 100 150 mV P - P
Ripple & Noise (20 MHz) Over Line, Load & Temp. 200 mV P - P
Ripple & Noise (20 MHz) 5 mV rms
Output Power Protection 120 %
Temperature Coefficient !0.01 !0.02 %/1C
Output Short Circuit Momentary (0.5 Sec.)
General
Parameter Conditions Min. Typ. Max. Units
Isolation Voltage 60 Seconds 1,000 VDC
Isolation Resistance 500 VDC 1,000 M
Isolation Capacitance 100 kHz, 1V 80 120 pF
Switching Frequency 50 80 100 kHz
Environmental
Parameter Conditions Min. Typ. Max. Units
Operating Temperature Range -40 +25 +70 1C
Storage Temperature Range -40 +125 1C
Cooling Free Air Convection
Humidity RH, Non-condensing 95 %
Physical
Case Size, 5V, 12V & 24V Input Models 0.80 x 0.40 x 0.27 Inches (20.32 x 10.16 x 6.85 mm)
Case Size, 48VDC Input Models 0.80 x 0.40 x 0.30 Inches (20.32 x 10.16 x 7.50 mm)
Case Material Non-Conductive Black Plastic
Weight 0.09 Oz (2.7g)
Reliability Specifications
Parameter Conditions Min. Typ. Max. Units
MTBF MIL HDBK 217F, 251C, Gnd Benign 3.6 MHours
Absolute Maximum Ratings
Parameter Conditions Min. Typ. Max. Units
5 VDC Input -0.7 9.0
12 VDC Input -0.7 18.0
Input Voltage Surge (1 Sec) VDC
24 VDC Input -0.7 30.0
48 VDC Input -0.7 55.0
Internal Power Dissipation All Models 650 mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
CompuMess Elektronik GmbH · Lise-Meitner-Str.1 · 85716 Unterschleissheim
Tel 089-321501-0 · Fax 089-321501-11 · www.compumess.de · www.netzteile.de
Model Selection Guide
Input Output Load Fuse Rating
Model Efficiency
Voltage (VDC) Current (mA) Voltage Current Current Regulation Slow-Blow
Number (%, Typ)
Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) (mA)
G201 5 4.5 - 5.5 452 35 3.3 500.0 10.0 11 73 1,000
G202 5 4.5 - 5.5 526 35 5.0 400.0 8.0 11 76 1,000
G203 5 4.5 - 5.5 495 35 12.0 165.0 3.0 7 80 1,000
G204 5 4.5 - 5.5 499 35 15.0 133.0 2.5 7 80 1,000
G205 5 4.5 - 5.5 519 35 !5.0 !200.0 !4.0 10 77 1,000
G206 5 4.5 - 5.5 504 35 !12.0 !83.0 !1.5 7 79 1,000
G207 5 4.5 - 5.5 501 35 !15.0 !66.0 !1.0 7 79 1,000
G211 12 10.8 - 13.2 185 25 3.3 500.0 10.0 8 74 500
G212 12 10.8 - 13.2 212 25 5.0 400.0 8.0 8 78 500
G213 12 10.8 - 13.2 200 25 12.0 165.0 3.0 5 82 500
G214 12 10.8 - 13.2 200 25 15.0 133.0 2.5 5 83 500
G215 12 10.8 - 13.2 222 25 !5.0 !200.0 !4.0 8 75 500
G216 12 10.8 - 13.2 201 25 !12.0 !83.0 !1.5 5 82 500
G217 12 10.8 - 13.2 200 25 !15.0 !66.0 !1.0 5 82 500
G221 24 21.6 - 26.4 92 10 3.3 500.0 10.0 8 74 200
G222 24 21.6 - 26.4 108 10 5.0 400.0 8.0 8 77 200
G223 24 21.6 - 26.4 101 10 12.0 165.0 3.0 5 81 200
G224 24 21.6 - 26.4 101 10 15.0 133.0 2.5 5 82 200
G225 24 21.6 - 26.4 111 10 !5.0 !200.0 !4.0 8 75 200
G226 24 21.6 - 26.4 102 10 !12.0 !83.0 !1.5 5 81 200
G227 24 21.6 - 26.4 100 10 !15.0 !66.0 !1.0 5 82 200
G231 48 43.2 - 54.8 28 6 3.3 500.0 10.0 8 74 100
G232 48 43.2 - 54.8 27 6 5.0 400.0 8.0 8 77 100
G233 48 43.2 - 54.8 26 6 12.0 165.0 3.0 5 81 100
G234 48 43.2 - 54.8 25 6 15.0 133.0 2.5 5 82 100
G235 48 43.2 - 54.8 28 6 !5.0 !200.0 !4.0 8 75 100
G236 48 43.2 - 54.8 26 6 !12.0 !83.0 !1.5 5 81 100
G237 48 43.2 - 54.8 25 6 !15.0 !66.0 !1.0 5 82 100
Notes: Derating Curve
1. Dual output units may be connected to provide a 10V, 100
24V or 30 VDC output. To do this, connect the load
across the positive (+Vout) and negative (-Vout)
outputs and float the output common. 80
2. These units do not require external comonents to
Output Power %
operate, but the use of an input capacitor (10 µF) may
60
enhance performance in some applications. An output
capacitor (4.7 µF to 10 µF) may be used to reduce
ripple. 40
Mechanical Dimensions 20
Side "T"
0
-40 -20 0 5 15 25 35 45 55 65 75 85 95 105
0.12 Ambient Temperature 1C
(3.05)
0.10
(2.54) Pin Connections
0.10
(2.54) 0.60 (15.24) Pin Single Dual
1 -Vin -Vin
0.80 (20.32)
Capacitive Load
7 NC NC
Single Output Dual Output
8 No Pin Common µF Max µF Max
1 7
9 +Vout +Vout 470 !390
0.40
Bottom (10.2) 11 -Vout -Vout
14 11 9 8 14 +Vin +Vin
0.01 0.01 NC = No Connection
(0.25) (0.25) 0.05
(1.25)
Notes: All dimensions are typical in inches (mm)
Note: "T" = 0.27 (6.85) For 5, 12 & 24 VDC Input Models Tolerance x.xx = !0.01 (!0.25)
0.30 (7.50) For 48 VDC Input Models Pin 1 is marked by a "dot" or indentation on the top of the unit
CompuMess Elektronik GmbH · Lise-Meitner-Str.1 · 85716 Unterschleissheim
Tel 089-321501-0 · Fax 089-321501-11 · www.compumess.de · www.netzteile.de