G200EI Series
High Isolation, 2W
Low Cost, MiniDIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features: Input
· 2W Output Power Parameter Conditions Min. Typ. Max. Units
· Compact MiniDIP Case 5 VDC Input 4.5 5.0 5.5
· UL Approved (File E245422) Input Voltage Range 12 VDC Input 10.8 12.0 13.2 VDC
· Single & Dual Outputs 24 VDC Input 21.6 24.0 26.4
· 3,000 VDC Isolation Input Filter Internal Capacitor
· >3.5 MHour MTBF Reverse Polarity Input Current 0.3 A
· 24 Standard Models Output
· LOWEST COST!! Parameter Conditions Min. Typ. Max. Units
Output Voltage Accuracy ±1.0 ±3.0 %
Output Voltage Balance Dual Output , Balanced Loads ±1.0 %
Line Regulation For Vin Change of 1% ±1.2 %
Load Regulation See Model Selection Guide
Ripple & Noise (20 MHz) 100 150 mV P - P
Output Power Protection 120 %
Temperature Coefficient ±0.02 ±0.03 %/ºC
Output Short Circuit Momentary (1.0 Sec.)
RoHS Compliant General
Parameter Conditions Min. Typ. Max. Units
Isolation Voltage 60 Seconds 3,000 VDC
Isolation Resistance 500 VDC 1,000 M
Isolation Capacitance 100 kHz, 1V 60 pF
Switching Frequency 75 kHz
Environmental
Parameter Conditions Min. Typ. Max. Units
Operating Temperature Range Ambient -40 +25 +85 ºC
Storage Temperature Range -55 +125 ºC
Cooling Free Air Convection
Humidity RH, Non-condensing 95 %
Physical
Case Size (5V 12V & 24V Input Models) 0.80 x 0.32 x 0.39 Inches (20.4 x 8.2 x 10.0 mm)
MicroPower Direct
292 Page Street Case Material Non-Conductive Black Plastic (UL94-V0)
Suite D Weight 0.07 Oz (2.1g)
Stoughton, MA 02072 Reliability Specifications
USA
Parameter Conditions Min. Typ. Max. Units
T: (781) 344-8226 MTBF MIL HDBK 217F, 25ºC, Gnd Benign 3.5 MHours
F: (781) 344-8481 Safety Standards UL 1950, EN 60950, IEC 60950
E: sales@micropowerdirect.com Safety Approvals UL, cUL; File No. E245422
W: www.micropowerdirect.com
Absolute Maximum Ratings
Parameter Conditions Min. Typ. Max. Units
5 VDC Input -0.7 9.0
Input Voltage Surge (1 Sec) 12 VDC Input -0.7 18.0 VDC
24 VDC Input -0.7 30.0
Lead Temperature 1.5 mm From Case For 10 Sec 300 ºC
Internal Power Dissipation All Models 450 mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
CompuMess Elektronik GmbH · Lise-Meitner-Str. 1 · D-85716 Unterschleißheim
Telefon (089) 32 15 01 - 0 · Telefax (089) 32 15 01 - 11
info@compumess.de · www.compumess.de · www.netzteile.de
Model Selection Guide
Input Output Load Fuse Rating
Model Efficiency
Voltage (VDC) Current (mA) Voltage Current Current Regulation Slow-Blow
Number (%, Typ)
Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) (mA)
G201EI 5 4.5 - 5.5 500 30 5.0 400.0 40.0 15 80 1,000
G202EI 5 4.5 - 5.5 494 30 9.0 222.0 23.0 15 81 1,000
G203EI 5 4.5 - 5.5 488 30 12.0 167.0 17.0 15 82 1,000
G204EI 5 4.5 - 5.5 476 30 15.0 133.0 14.0 15 84 1,000
G205EI 5 4.5 - 5.5 488 30 ±5.0 ±200.0 ±20.0 15 82 1,000
G206EI 5 4.5 - 5.5 482 30 ±9.0 ±111.0 ±12.0 15 83 1,000
G207EI 5 4.5 - 5.5 470 30 ±12.0 ±83.0 ±9.0 15 85 1,000
G208EI 5 4.5 - 5.5 470 30 ±15.0 ±67.0 ±7.0 15 85 1,000
G211EI 12 10.8 - 13.2 208 15 5.0 400.0 40.0 15 80 500
G212EI 12 10.8 - 13.2 201 15 9.0 222.0 23.0 15 83 500
G213EI 12 10.8 - 13.2 198 15 12.0 167.0 17.0 15 84 500
G214EI 12 10.8 - 13.2 196 15 15.0 133.0 14.0 15 85 500
G215EI 12 10.8 - 13.2 201 15 ±5.0 ±200.0 ±20.0 15 83 500
G216EI 12 10.8 - 13.2 198 15 ±9.0 ±111.0 ±12.0 15 84 500
G217EI 12 10.8 - 13.2 194 15 ±12.0 ±83.0 ±9.0 15 86 500
G218EI 12 10.8 - 13.2 194 15 ±15.0 ±67.0 ±7.0 15 86 500
G221EI 24 21.6 - 26.4 103 8 5.0 400.0 40.0 15 81 250
G222EI 24 21.6 - 26.4 99 8 9.0 222.0 23.0 15 84 250
G223EI 24 21.6 - 26.4 98 8 12.0 167.0 17.0 15 85 250
G224EI 24 21.6 - 26.4 97 8 15.0 133.0 14.0 15 86 250
G225EI 24 21.6 - 26.4 99 8 ±5.0 ±200.0 ±20.0 15 84 250
G226EI 24 21.6 - 26.4 98 8 ±9.0 ±111.0 ±12.0 15 85 250
G227EI 24 21.6 - 26.4 96 8 ±12.0 ±83.0 ±9.0 15 87 250
G228EI 24 21.6 - 26.4 96 8 ±15.0 ±67.0 ±7.0 15 87 250
Notes:
1. Output load regulation is specified for a load change of 10% to
Derating Curve
100%.
2. These units should not be operated with a load under 10% of
full load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended
that an external ceramic capacitor be placed from the +Vout
pin to the -Vout pin for single output units and from each out-
put to common for dual output units. An input capacitor will
enhance stability over temperature and input line variations.
Recommended capacitor values are given in the table below.
For applications requiring very low output noise levels, a simple
LC filter should be effective.
Input Output Capacitor
Vin Vout
Capacitor Single Dual
5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF
12 VDC 2.2 µF 9 VDC 4.7 µF 2.2 µF
24 VDC 1.0 µF 12 VDC 2.2 µF 1.0 µF Mechanical Dimensions
15 VDC 1.0 µF 0.47 µF
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the posi-
tive (+Vout) and negative (-Vout) outputs and float the output
common
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for
the correct rating.
Pin Connections
Pin Single Dual Pin Single Dual
1 -Vin -Vin 9 No Pin Common
7 NC NC 10 -Vout -Vout
8 +Vout +Vout 14 +Vin +Vin
Notes:
· All dimensions are typical in inches (mm)
· Tolerance x.xx = ±0.01 (±0.25)
· Pin 1 is marked by a "dot" or indentation on the top of the unit
MicroPower Direct
www.micropowerdirect.com
CompuMess Elektronik GmbH · Lise-Meitner-Str. 1 · D-85716 Unterschleißheim
292 Page Street Ste D Stoughton, MA 02072 Telefon (781) 344-8226 - 0 · FAX: (781) 344-8481 01 -E-Mail: sales@micropowerdirect.com
· TEL: (089) 32 15 01 · Telefax (089) 32 15 · 11
info@compumess.de · www.compumess.de · www.netzteile.de