Hier Klicken für das PDF Dokument!!!
Digibridge 1715 LCR Meter
Passive Component Tester with RS-232
USES: Introduction
· Production Testing of LCR Components The QuadTech 1715 LCR Digibridge is an economically priced, easily pro-
grammable, micro-processor based passive component tester for fast, precise
· Component Design and Evaluation
impedance measurements. It measures eleven different parameters with a
· Component Inspection and Screening basic accuracy of 0.2%. The 1715 provides four different test frequencies and
· Quality Assurance Testing two test voltages for testing flexibility. For remote operation and automated
system applications, the unit comes standard with an RS-232 interface, plus
· Material Testing IEEE-488 and Handler interfaces are available as options.
Description
FEATURES: 11 Measurement Parameters: Measure and display two of 11 impedance
· 11 Measurement Parameters parameters simultaneously with a basic accuracy of 0.2%. Test results can also
be shown as Deviation or %Deviation from nominal value.
· 0.2% Basic Measurement Accuracy
Test Signal: Four user selectable test frequencies: 100Hz, 120Hz, 1kHz, and
· Selectable Test Frequency: 100Hz, 10kHz (9.6kHz), plus two test voltages: 0.25V and 1.0V.
120Hz, 1kHz, 10kHz Display: 40 x 4 character LCD display for user friendly menu programming
· Selectable Test Voltage: 0.25V, 1.0V and measured results. Simultaneously displays primary/secondary values and
· Measurement Speed to 25/second binning or comparator results.
Setup Storage: Storage of 1 setup with parameter, binning and compare infor-
· LCD Display mation saved. Auto recall of this setup upon power-up of instrument.
· RS-232 Interface Standard Auto Ranging: For maximum measurement integrity the 1715 automatically
· IEEE and Handler Interfaces, Optional selects the appropriate measurement range and instrument source impedance
· Automatic Open/Short Zeroing (25, 100, 1k, 10k or 100k), dependent upon the impedance of the
device under test.
· Automatic Hi/Lo Comparator Limits Pass/Fail Testing: The 1715 provides a programmable Hi/Lo comparator
· Pass/Fail Sorting (8 Bins) function as well as eight sorting bins for categorization of components.
· Storage of 1 Setup Open/Short Zeroing: Reduce the effects of error sources (stray
admittance/residual impedance) between the device under test and the cali-
· Automatic Source Impedance Selection
brated connection to the measuring instrument.
· Keypad Lockout Interfaces: For remote control, or adaption to a production environment, the
· Easy Operation 1715 instrument includes an RS-232 interface as standard equipment. Both an
· Programmable Delay Time IEEE-488 and a Handler interface are available as optional interfaces.
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
HIPOT · LCR METERS · MEGOHMMETERS · MILLIOHMMETERS
1715 Digibridge LCR Features
Parameter Measurement Range Interfaces (Standard): RS-232
Ls, Lp 0.01uH - 9.999kH Interfaces (Optional): IEEE-488 and Handler
Cs, Cp 0.01pF - 99.999mF
Rs, Rp 0.1m - 99.99M Test Terminals: Front: 4 BNC & 1 GND
D 0.0001 - 9999 Dimensions: (w x h x d): 12.5 x 4.0 x 8.0in
Q 0.0001 - 9999 (312.5 x 100.0 x 200.0mm)
lZl 0.1m - 99.99M
Weight: 10.85 lbs. (5kg) net, 15.2 lbs. (7kg) ship
Xs 0.1m - 99.99M
Phase -180.00° - +180.00° Environmental: Specifications: +15°C to +35°C, 75% RH
Accuracy: Basic LCR ±0.2% Operating: 10°C to +40°C
Storage: 0°C to +50°C
Basic DQ ±0.002
Humidity: 10 -90% RH
Test Frequency: 100Hz, 120Hz, 1kHz and 10kHz (9.6kHz) Pollution Degree 2
Accuracy ±0.2% Installation Category II
Test Signal: 0.25V or 1.0V RMS, ±(10% + 3mV) Power: · 90 - 125V AC
Measurement Speed: Fast: 25 measurements/second · 190 - 250V AC
Medium: 8 measurements/second · 48 - 62 Hz
Slow: 2 measurements/second · 50VA max
Measurement Mode: Continuous or Trigger
Trigger: Internal
External (IEEE or Handler)
Manual
Trigger Delay: 0 - 9999ms
Ranging: Automatic or Hold Range
Equivalent Circuit: Series or Parallel
Zeroing: Open and short circuit compensation
Source Impedance: 25, 100, 1k, 10k or 100k
(based on DUT impedance)
Comparator: Primary Nominal
Primary Hi/Lo Limits (Value or %)
Secondary Hi/Lo Limuts (Value or %)
Indication: Audible Alarm programmable: HI LO or
OFF for Pass or Fail Result
Binning: Primary Nominal
Primary Hi/Lo Limits (8 Bins in %)
Secondary Hi/Lo Limits (Value)
Display: 40 by 4 Character LCD display
Results Format: Value
Deviation
% Deviation
Bin Number
Setup Storage: Store 1 setup, Auto recall upon power-up
Lock: Keypad Lockout
Ordering Information
1715 LCR Digibridge Optional Accessories:
B/A Calibration Data
Includes:
1700-01 Axial/Radial Component Test Fixture
QuadTech P/N Item
1700-02 Axial/Radial Remote Test Fixture
150710 1715 Instruction Manual
1700-03 Lead Set: 4 BNC Connectors to 2 Kelvin Clips
1700-03 Lead Set: 4 BNC Connectors to 2 Kelvin Clips
1700-04 Lead Set: 4 BNC Connectors to 4 Banana Plugs
4200-0300 AC Power Cord
1700-05 Lead Set: 4 BNC Connectors to Chip Component Tweezers
520023/520025 Power Line Fuses (0.630A 250V/0.315A 250V)
7000-07 Low Voltage Chip Component Test Fixture
Calibration Certificate Traceable to NIST
700171 IEEE-488 & Handler Interface
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
Digibridge 1730T LCR Meter
USES: with Turns Ratio for Transformer Testing
· Transformer/Coil Testing Introduction
· Production Testing The QuadTech 1730T LCR Meter is an easily programmable, microprocessor-
based high performance passive component tester with excellent low impedance
· Component Screening measurement and fast measurement speeds even at 100/120Hz. It measures 16 dif-
· Material Testing ferent parameters with a basic accuracy of 0.1%. Programmable test frequency,
speed, mode and voltage permits great versatility in component and materials test-
· Quality Assurance Testing ing. Standard IEEE-488 and Handler interfaces provide data transfer and compo-
· Component Design and Evaluation nent automation applications for faster production line testing.
FEATURES: Description
14 Measurement Parameters: Measure and display two of 16 impedance param-
· 14 Measurement Parameters eters simultaneously with a basic accuracy of 0.1%. Test results can also be shown
· 0.1% Basic Measurement Accuracy as Deviation or %Deviation from nominal value.
10 Test Frequencies: User selectable: 50Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz,
· 10 Test Frequencies: 50Hz-100kHz 20kHz, 40kHz, 50kHz and 100kHz.
· Test Voltage: 10mV-1V Transformer Testing: Use the Turns Ratio function to measure the DCR of the pri-
· Measurement Speeds up to 62/second mary coil, N and 1/N for both coils, and M the mutual inductance between the coils.
LCD Display: Large, high resolution graphic display for clear, concise results and
· Monitor DUT Voltage and Current user friendly menu interface for easy programming.
· Large High Res. Graphic Display Setup Store/Recall: Store/Recall up to 50 test setups from instrument memory.
· IEEE and Handler Interfaces, Std. Lock out front panel to ensure procedures are run the same way every time.
Programmable Source Impedance: Program tester impedance to 100,
· Automatic Open/Short Zeroing 100/25, 25 or 10 constant current when comparing results with measurements
· Pass/Fail Binning (8) made on other testers. Measurement results can vary significantly based solely on
the source impedance of the tester being used.
· Storage/Recall of 50 Setups
Voltage/Current Monitoring: Use the test signal monitoring function to display
· Measurement Averaging (1-256) the actual voltage level across and current through the DUT.
· Measurement Delay (0-10 seconds) DC Bias: External DC Bias voltage from 0-5V, permits capacitors to be tested
under real DC bias conditions. Measurement of External DC Bias Current to 20A
· Programmable Source Impedance is possible using the 1730T and the 1320 Bias Current Source.
· DC Bias Voltage (0-5V) Open/Short Zeroing: Reduce the effects of error sources (stray admittance/resid-
· Keypad Lockout ual impedance) between the DUT and the calibrated connection to the measuring
instrument.
· Easy Operation Fast Testing: Select from one of three measurement speeds: slow, medium or fast
· Cable Correction 0-4M for varying degrees of accuracy and speed up to 62 measurements/second.
· Turns Ratio & DCR Measurements Interfaces Standard: The 1730T unit includes IEEE-488 and Handler interfaces
for adaption into production environments or remote control applications.
For more detailed
specifications, visit
www.quadtech.com
For more information about special
purchase, rent & lease options, call
1-800-253-1230
Fax 1-978-461-4295
Intl. 1-978-461-2100
HIPOT · LCR METERS · MEGOHMMETERS · MILLIOHMMETERS · CABLE TESTERS
1730T LCR Meter Features
Product Specifications
Parameter Measurement Range Measurement Delay: Programmable from 0-10s in 1ms steps
Ls, Lp 0.001uH - 99.999kH Averaging: Programmable from 1-256
Cs, Cp 0.001pF - 9.9999F
Rs, Rp 0.01m - 99.99M Binning: Eight pass bins for LCR
L2A, L2B 0.001uH - 99.999kH One fail bin, LCR and DQ
D 0.0001 - 9999 Interfaces: IEEE-488 and Handler Standard
Q 0.0001 - 9999
Equivalent Circuit: Series or Parallel
ESR 0.01m - 99.99M
lZl 0.01m - 99.99M Zeroing: Open and short circuit compensation.
Xs 0.01m - 99.99M Buzzer: Programmable: HI LO or OFF for Pass or
Phase -180.00° - +180.00° Fail Result
M 0.001µH - 99.999kH
Comparator: Set Upper/ Lower Limit as absolute value
N 0.001T - 9999.9
or % value for primary and secondary
1/N 0.001T - 9999.9
parameters
DCR 0.01m - 99.99M
Test Signal: Monitor voltage across and current
Accuracy: Basic LCR ±0.1%. through device under test.
Basic DQ ±0.001 Test Terminals: Front: 4 BNC & 1 GND
Test Frequencies: 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, Rear: EXT BIAS: 1 BNC, 2-terminal strip
50kHz and 100kHz Setup Storage: Store/Recall 50 test setups
Accuracy ±(0.01% ± 0.01Hz) Lock: Keypad Lockout
Measurement Speed: Fast: 62 measurements/second Dimensions: (w x h x d): 12.5 x 4.0 x 13.5in
Medium: 19 measurements/isecond (312.5 x 100.0 x 337.5mm)
Slow: 3 measurements/second
Weight: 12.4 lbs. (5.7kg) net, 17 lbs. (7.8 kg) ship
Ranging: Automatic or User Selectable
Trigger: Internal Enviromental: Specifications: +15°C to +35°C, 75% RH
External (IEEE or Handler) Operating: 0°C to +50°C
Manual Storage: -40°C to +75°C
Humidity: <85%
Source Impedance: 100/25, 100, 25 or 10c.c. (constant
current) Power: · 90 - 125V AC
· 190 - 250V AC
AC Test Signal: Voltage: 10mV - 1V, 10mV steps · 50 or 60 Hz
DC Bias Voltage: External: 0-5V · 65W max
Internal: 0-5V with RBIAS external resistor
DC Bias Current: Internal: 0-200mA with RBIAS ext resistor
External: 0-20A with 1320 BC Source;
External: 0-100A with 1320 BC Source
and four 1320S Slave Units
Display: 240 by 64 LCD display
Results Format: Value
Deviation
% Deviation
Bin Number
GO/NO GO
Ordering Information
1730T LCR Meter Optional Accessories:
B/A Calibration Data
Includes:
1700-01 Axial/Radial Component Test Fixture
QuadTech P/N Item
1700-02 Axial/Radial Remote Test Fixture
4200-0300 AC Power Cord
1700-03 Kelvin Lead Set: 4 BNC Connectors to 2 Kelvin Clips
150821 Instruction Manual
7000-01 BNC to BNC Cable Lead Set (1m)
520026/520138 Power Line Fuses (1.0A 250V/0.5A 250V)
7000-02 BNC to BNC Cable Lead Set (2m)
1700-03 Kelvin Test Leads: 4 BNC to 2 Kelvin Clips
7000-05 Lead Set: 4 BNC Connectors to Chip Component Tweezers
630166 Transformer Test Fixture: 4 BNC to 4 Alligator Clips
7000-07 Low Voltage Chip Component Test Fixture
Calibration Certificate Traceable to NIST
630166 Transformer Test Fixture: 4 BNC to 4 Alligator Clips
For more detailed specifications, visit www.quadtech.com
For more information about special purchase, rent & lease options, call Unterschleissheim
CompuMess Elektronik GmbH · Lise-Meitner-Str.1 · 85716
Tel 089-321501-0 · Fax 089-321501-11 · www.compumess.de · www.netzteile.de
1-800-253-1230 · Fax 1-978-461-4295 · Intl. 1-978-461-2100
5 Clock Tower Place, 210 East, Maynard MA 01754 P/N 030148/A1
1910 Inductance Analyzer
USES: A High Performance Tester
· Production Testing of Inductive Introduction
Components & Wire Wound Devices The 1910 is a production oriented, Inductance Analyzer, with a programmable frequency
· AC Impedance & DC Resistance range of 20Hz to 1MHz, designed to perform inductance and other impedance measure-
Measurements on a Wide Variety of ments on coils and wire wound devices. The unit is also capable of measuring DC resist-
ance between 0.1m and 100k and provides voltage or current monitoring to the test
Components device. The 1910 also provides a sequence testing mode, allowing up to 6 unique tests
· Inductance Measurements Under DC with one single start command. With its user friendly menu programming, automatic lead
Bias Current Conditions zeroing, and 5 digit measurement resolution the instrument provides fast and accurate
test results.
· Component Design & Evaluation
Description
20 Measurement Parameters Measure and display any two of 15 impedance param-
FEATURES: eters simultaneously, with a basic accuracy of 0.1%. Additionally the 1910 can measure
· 20 Measurement Parameters the DC resistance, or display the current through or voltage across a test device ensuring
the operator of the real test conditions.
· Frequency Range 20 Hz to 1MHz
Wide Frequency Over 27,000 user programmable test frequencies to fully characterize
· 0.1% Basic Measurement Accuracy devices over the range of 20 Hz to 1 MHz.
· Measurement Speeds Up to 40/sec Automatic Test Sequencing For increased productivity and throughput the 1910 can
· DC Resistance Measurements perform up to six different tests in sequence with a single push of the start button. Each
test can have different measurement parameters, test conditions and limits.
· Monitoring of DUT Voltage and
DC Current Bias The instruments programmable internal DC bias current source from
Current 1 mA to 1 Amp allows components to be tested under real operating conditions. This can
· 5 Digit Measurement Resolution be expanded to 100 Amps when the 1910 is used in conjunction with QuadTech's Model
1320 Bias Current Source and slave units
· Constant Voltage (Voltage Leveling)
Setup Storage/Recall The test operator has the ability to store and recall, from inter-
· IEEE-488, RS-232 & Handler nal memory, up to 30 single test setups and 10 sequential setups (six tests in sequence).
Interfaces, all Standard The front panel can be locked out, with password protection, to ensure that procedures
are run the same way every time.
· Open/Short Zeroing & Cable
Compensation Load Correction Substantially improves instrument accuracy by allowing the operator
to specify the value of a known standard, measure it, and apply a correction to ongoing
· Load Correction measurements.
· 14 Pass/Fail Bins Programmable Source Impedance The operator is able to set instrument source
impedance at 5, 25, 50 or 100 ohms, an important feature when comparing measure-
· Keypad Lockout
ments to those made on other another testers. Measurement results can vary substantial-
ly based solely on the source impedance of the tester being used.
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
HIPOT · LCR METERS · MEGOHMMETERS · MILLIOHMMETERS · TRANSFORMER TESTERS
1910 Inductance Analyzer
Product Specifications
Parameter Measurement Range Basic Measurement Accuracy*
Low Medium High
Ls,Lp 0.001nH to 99.999H +/-0.5% +/-0.25% +/-0.1%
Cs,Cp 0.01pF to 9.9999F +/-0.5% +/-0.25% +/-0.1%
DF 0.00001 to 99.999 +/-0.005 +/-0.0025 +/-0.001
Q 0.00000 to 9999.9 +/-0.005 +/-0.0025 +/-0.001
Y,Gp,Bp 10 nS to 9999.9 S +/-0.5 +/-0.25 +/-0.1
|Z|,Rs,Rp,Xs,ESR 0.00001 m to 99.999M +/-0.5% +/-0.25% +/-0.1%
Phase Angle -180.00 to +179.99 degrees +/-1.8° +/-0.9° +/-0.18°
DCR 0.1m to 100K +/-0.5% +/-0.25% +/-0.1%
DUT AC Voltage 20mV to 1.0V +/-(2% + 5mV)@1kHz
DUT AC Current 1µA to 150mA +/-(2% + 5µA)@1kHz
DUT DC Voltage 20mV to 1.0V +/-(2% + 5mV)
DUT DC Current 1µA to 150mA +/-(2% + 5µA)
*At optimum test signal levels, frequencies, DUT values and without calibration uncertainty.
Test Frequency: Range: 20Hz to 1MHz, Continuous Measurement Delay: Programmable from 0 to 1000 ms in 1ms steps
Resolution: 1Hz from 20Hz to 1KHz,
Averaging: Programmable from 1 to 1000
4 digits >1KHz
Accuracy: +/- (0.02% +0.02 Hz) Median Value: Averaged over last three measurements
Measurement Speed: Speed Accuracy Setting Setup Storage: 30 Single Tests
40 meas/sec Low, No Display 10 Sequential (6 tests in each)
25 meas/sec Low
Other: Constant Voltage Mode (voltage leveling)
10 meas/sec Medium
Cable Compensation (1M, 2M, no cable)
1 meas/sec High
Open/Short Zeroing
Ranging: Automatic, Range Hold or user selectable Distortion Check
Trigger: Internal (automatic) Calibration·: Recommended interval 1 year
External (via RS-232,IEEE-488.2 or Handler NIST traceable calibration
interfaces) Built-in automatic calibration procedure
Manual
Usage & Cal Data: Displays last calibration date, standard values used
Source Impedance: 5, 25, 50, 100 in calibration
AC Test Signal: Voltage: 20mV to 1.0V (open circuit) in 5 mV Self Test: Verifies critical instrument operation at power-up or
steps when selected from menu
DC Test Signal: Voltage: 20mV to 1.0V (open circuit) in 5 mV Test Terminals: Front panel, four terminal (BNC)
steps, 5 source impedance Optional Test Fixtures Available
DC Bias Current: Internal: 0.0 to 1.0A in 1mA steps Mechanical: Bench mount with tilt bail
External: 0.0 to 20.0A in 5mA steps using Rack mount kit optional
QuadTech 1320
Dimensions: (w x h x d): 17 x 5.25 x 16in (432 x 133 x 406 mm)
Display: LCD Display with backlight
Weight: 15lbs (8kg) net, 21lbs (9.9kg) shipping
Pass/Fail and status indicators
Enviromental: Meets MIL-28800E, Type 3, Class 5, Style E & F
Results Formats: Engineering or scientific format
Operating: 0° to +50°C
%Deviation from nominal of primary parameter
Humidity: < 75% for 11° to 30°C operating
Deviation from nominal of primary parameter
Storage: -40° to +71° C
Pass/Fail
No Display Mode for maximum throughput Power: 100-240 VAC 50/60 Hz
100 W Max
Sequencing:
Displays up to 6 sequential test results, primary
and/or secondary CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Standard Interfaces: IEEE-488.2, RS-232, Handler Tel 089-321501-0 Fax 089-321501-11
Ordering Information http://www.compumess.de oder http://www.netzteile.de
1910 Inductance Analyzer 1700-02 Axial/Radial Remote Test Fixture
Includes: 1700-03 4 BNC Connectors to 2 Kelvin Clips Lead Set
4200-0300 AC Power Cord 1700-04 4 BNC Connectors to 4 Banana Plugs
150491 Instruction Manual 1700-05 4 BNC Connectors to Chip Component Tweezers
Calibration Certificate 2000-16 Rack Mount Flanges
Traceable to NIST 7000-01 BNC to BNC Cable Set (1M)
7000-02 BNC to BNC Cable Set (2M)
Optional Accessories
7000-07 Low Voltage Chip Component Test Fixture
1700-01 Axial/Radial Component
Test Fixture
PN030091/A1
Series 1920 Precision LCR Meter
USES: High Performance Testing to 1 MHz
· Fast Production Testing of LCR Introduction
Components and Materials The 1920 is a high performance LCR Meter designed to perform fast, automated
· AC Impedance & DC Resistance impedance measurements on a variety of electronic components and materials. The
Measurements instrument has a basic accuracy specification of 0.1% for accurate test results over
a wide frequency range, from 20 Hz to 1 MHz. Besides 15 impedance parameters the
· Component Characterization Over 1920 is also capable of measuring DC resistance as well as monitoring the voltage
a Wide Frequency Range across or current through the device under test. The unit incorporates a distinctive
sequence test mode, allowing up to 6 uniquely different tests to be performed quickly
· Component Screening, Evaluation on a single start command. Additionally, the 1920 includes IEEE-488, RS-232, and
and Design handler interfaces, all standard.
Description
FEATURES: 20 Measurement Parameters Measure and display any two of 15 impedance
· 20 Measurement Parameters parameters simultaneously, with a basic accuracy of 0.1%. Additionally the 1920 can
measure the DC resistance, or display the current through or voltage across a test device
· Frequency Range 20 Hz to 1MHz ensuring the operator of the real test conditions.
· 0.1% Basic Measurement Accuracy Wide Frequency Over 27,000 user programmable test frequencies to fully characterize
· Measurement Speeds Up to 40/sec devices over the range of 20 Hz to 1 MHz.
· DC Resistance Measurements Automatic Test Sequencing For increased productivity and throughput the 1920 can
perform up to six different tests in sequence with a single push of the start button. Each
· Monitoring of DUT Voltage and test can have different measurement parameters, test conditions and limits.
Current DC Bias Voltage The instruments internal DC bias voltage source, programmable from
· 5 Digit Measurement Resolution 0 to 2 V in 1 mV steps, allows capacitors to be tested under real DC bias conditions.
· Programmable DC Bias Voltage, 0-2V Setup Storage/Recall The test operator has the ability to store and recall, from
internal memory, up to 30 single test setups and 10 sequential setups (six tests in
· Constant Voltage (Voltage Leveling) sequence). The front panel can be locked out, with password protection, to ensure that
· IEEE-488, RS-232 & Handler procedures are run the same way every time.
Interfaces, all Standard Load Correction Substantially improves instrument accuracy by allowing the operator
to specify the value of a known standard, measure it, and apply a correction to ongoing
· Open/Short Zeroing & Cable measurements.
Compensation
Programmable Source Impedance The operator is able to set instrument source
· Load Correction impedance at 5, 25, 50 or 100 ohms, an important feature when comparing measure-
ments to those made on other testers. Measurement results can vary substantially based
· 14 Pass/Fail Bins
solely on the source impedance of the tester being used.
· Keypad Lockout
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
F
HIPOT & GROUND BOND TESTERS · LCR METERS · MEGOHMMETERS · MILLIOHMMETERS
1920 Precision LCR Meter
Product Specifications
Parameter Measurement Range Basic Measurement Accuracy*
Low Medium High
Ls,Lp 0.001nH to 99.999H +/-0.5% +/-0.25% +/-0.1%
Cs,Cp .01pF to 9.9999F +/-0.5% +/-0.25% +/-0.1%
DF 0.00001 to 99.999 +/-0.005 +/-0.0025 +/-0.001
Q 0.00000 to 9999.9 +/-0.005 +/-0.0025 +/-0.001
Y,Gp,Bp 10 nS to 9999.9 S +/-0.5% +/-0.25% +/-0.1%
|Z|,Rs,Rp,Xs,ESR 0.00001 m to 99.999M +/-0.5% +/-0.25% +/-0.1%
Phase Angle -180.00 to +179.99 degrees +/-1.8° +/-0.9° +/-0.18°
DCR 0.1m to 100K +/-0.5% +/-0.25% +/-0.1%
DUT AC Voltage 20mV to 1.0V +/-(2% + 5mV)@1kHz
DUT AC Current 1µA to 150mA +/-(2% + 5µA)@1kHz
DUT DC Voltage 20mV to 1.0V +/-(2% + 5mV)
DUT DC Current 1µA to 150mA +/-(2% + 5µA)
*At optimum test signal levels, frequencies, DUT values and without calibration uncertainty.
Test Frequency: Range: 20Hz to 1MHz, Continuous Measurement Delay: Programmable from 0 to 1000 ms in 1ms steps
Resolution: 1Hz from 20Hz to 1KHz,
Averaging: Programmable from 1 to 1000
4 digits >1KHz
Accuracy: +/- (0.02% +0.02 Hz) Median Value: Averaged over last three measurements
Measurement Speed: Speed Accuracy Setting Setup Storage: 30 Single Tests
40 meas/sec Low, No Display 10 Sequential (6 tests in each)
25 meas/sec Low
Other: Constant Voltage Mode (voltage leveling)
10 meas/sec Medium
Cable Compensation (1M, 2M, no cable)
1 meas/sec High
Open/Short Zeroing
Ranging: Automatic, Range Hold or user selectable Distortion Check
Trigger: Internal (automatic) Calibration: Recommended interval 1 year
External (via RS-232,IEEE-488.2 or Handler NIST traceable calibration
interfaces) Built-in automatic calibration procedure
Manual
Usage & Cal Data: Displays last calibration date, standard values used
Source Impedance: 5, 25, 50, 100 in calibration
AC Test Signal: Voltage: 20mV to 1.0V (open circuit) in 5 mV Self Test: Verifies critical instrument operation at power-up or
steps when selected from menu
DC Test Signal: Voltage: 20mV to 1.0V (open circuit) in 5 mV Test Terminals: Front panel, four terminal (BNC)
steps, 5 source impedance Optional Test Fixtures Available
DC Bias Voltage: Internal: 0 to 2V in 1mV steps Mechanical: Bench mount with tilt bail
Rack mount kit optional
Display: LCD Display with backlight
Pass/Fail and status indicators Dimensions: (w x h x d): 17 x 5.25 x 16in (432 x 133 x 406 mm)
Results Formats: Engineering or scientific format Weight: 15lbs (8kg) net, 21lbs (9.9kg) shipping
%Deviation from nominal of primary parameter
Enviromental: Meets MIL-28800E, Type 3, Class 5, Style E & F
Deviation from nominal of primary parameter
Operating: 0° to +50°C
Pass/Fail
Humidity: < 75% for 11° to 30°C operating
No Display Mode for maximum throughput
Storage: -40° to +71° C
Sequencing:
Power: 100-240 VAC 50/60 Hz
Displays up to 6 sequential test results, primary
100 W Max
and/or secondary
Standard Interfaces: IEEE-488.2, RS-232, Handler
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Ordering Information Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
1920 Precision LCR Meter 1700-02 Axial/Radial Remote Test Fixture
Includes: 1700-03 4 BNC Connectors to 2 Kelvin Clips Lead Set
4200-0300 AC Power Cord 1700-04 4 BNC Connectors to 4 Banana Plugs
150566 Instruction Manual 1700-05 4 BNC Connectors to Chip Component Tweezers
Calibration Certificate 2000-16 Rack Mount Flanges
Traceable to NIST 7000-01 BNC to BNC Cable Set (1M)
7000-02 BNC to BNC Cable Set (2M)
Optional Accessories
7000-07 Low Voltage Chip Component Test Fixture
1700-01 Axial/Radial Component
Test Fixture
PN030092/A1
Series 7000 Precision LCR Meters
USES: CE Marked Impedance Analyzer
· Production Testing of LCR
Components Introduction
The 7000 LCR Meter is designed to perform precision impedance measurements over a
· Frequency Response Characterization wide frequency range, 10 Hz to 500 kHz for the model 7400 and 10 Hz to 2 MHz for the
of Components 7600. The instrument is capable of measuring 14 different parameters with 0.05% accu-
· Component Screening racy to meet today's requirements for component and material testing. The ease of use
and user friendly menu programming makes the 7000 Series ideal for applications in
· Material Testing product development, incoming inspections, or production line testing.
· Quality Assurance Testing
Description
· Measuring Dielectric Constant Using 14 Different Impedance Parameters Measure and display any two parame-
Standard Test Cell ters simultaneously to achieve coverage and flexibility not previously available.
FEATURES: Automatic Test Sequencing Run up to six different tests in sequence with a sin-
· Frequency Range 10 Hz to 2 MHz gle push of the start button. Each test can have different conditions and limits.
(7600), 500 kHz (7400) Swept Measurements Fast and accurate swept parameter measurements, graphi-
· 0.05% Basic Measurement Accuracy cal or tabular, for verification of component and material response to changes in AC test
frequency, AC test voltage or AC test current, without the need for complex programming
· 7 Digit Measurement Resolution or an external controller.
· Programmable Test Voltage and
Program and Data Storage Test setups can be stored and recalled from either
Current
internal memory or from standard DOS formatted 3 1/2" floppy disks. The front panel
· Auto Ranging can be locked out, with password protection, to ensure procedures are run the same way
· Test Setup and Measurement Data every time. Measured data can be stored on a floppy disk and then transferred to PC for
data reduction and analysis.
Storage
· Four-Terminal Kelvin Connections Load Correction Substantially improves instrument accuracy by performing meas-
urements on a known standard and applying correction to subsequent measurements.
· IEEE-488, RS-232, Handler, and Ideal for repetitive testing of identical devices at like test conditions.
Parallel Printer Interfaces
Automatic Calibration Procedure The 7000 can be calibrated without return-
· Graphical and Tabular Display of
ing the unit to the factory using the NIST traceable QuadTech Calibration Kit, reducing
Swept Frequency, Voltage and Current downtime and calibration costs.
Measurements
· Sequence Testing of Up To 6 Easy to Use Large LCD graphics display and user friendly menu driven interface allows
the 7000 to be put on line fast, providing useful measurements by operators with little or
Individual Tests
no training.
· Load Correction CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
· Binning (15) Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
· Built-in Automatic Calibration Routine
HIPOT · LCR METERS · MEGOHMMETERS · MILLIOHMMETERS · DECADES · STANDARDS
Result Formats: Engineering or scientific notation
7400/7600
% Deviation from nominal of primary parameter
Measured Parameters: Any two of 14 parameters measured and
Deviation from nominal of primary parameter
Product Specifications
displayed simultaneously, user selectable
Pass/Fail
Basic Measurement Accuracy* Binning summary
Parameter Measurement Range Speed No Display for maximum throughput
Fast Medium Slow
Cs, Cp 00000.01 fF to 9.999999 F ±0.5% ±0.25% ±0.05% Sweep Result: Primary parameter vs. frequency, voltage or
Ls, Lp 0000.001 nH to 99.99999 H ±0.5% ±0.25% ±0.05% current
D .0000001 to 99.99999 ±0.005 ±0.0025 ±0.0005 Graphical or Tabular Format
Q .0000001 to 999999.9 ±0.005 ±0.0025 ±0.0005 Up to 200 measurement points per sweep
Z , Rs, Rp, 000.0001 m to 99.99999 M ±0.5% ±0.25% ±0.05% Sequencing Result: Displays up to 6 sequential test results, primary
ESR, Xs
and/or secondary
Y , Gp, Bp 00000.01 µS to 9.999999 MS ±0.5% ±0.25% ±0.05%
Phase Angle -180.0000 to +179.9999 degrees ±1.8° ±0.9° ±0.18° AutoAcc: Automatic calculation and display of overall
*At optimum test signal levels, frequencies, DUT values and without calibration uncertainty. instrument accuracy for selected settings, test
Capacitance (Cs/Cp), Inductance (Ls/Lp), Resistance (Rs/Rp), Dissipation (D) and Quality (Q) conditions and device under test
Factors, Impedance Z , Admittance Y , Phase Angle (0 Equivalent Series Resistance (ESR),
-),
Conductance (Gp), Reactance (Xs), Susceptance (Bp) Standard Interfaces: IEEE-488.2, RS-232, Handler, Printer Port,
Note: s = series, p = parallel, ESR equivalent to Rs
3.5" Disk Drive
Test Frequency: 7400 Range: 10 Hz to 500 kHz, continuous Charged Capacitor Protection: 8/C for Vmax 250 V; 2/C for Vmax 1000V
Resolution: 0.1 Hz from 10 Hz to C = Capacitance in farads of the device under test
10 kHz, 5 digits>10kHz Additional Fuse Protection on 7400C
Accuracy: +/-(0.002% + 0.02Hz)
7600 Range: 10 Hz to 2 MHz, continuous Measurement Delay: Programmable from 0 - 1000 ms in 1 ms steps
Resolution: 0.1 Hz from 10 Hz to Averaging: Programmable from 1 - 1000
10 kHz, 5 digits>10kHz Median value mode
Accuracy: +/-(0.25% + 0.02Hz)
Data Storage: 40,000 measurements/disk
Measurement Speed: 7400 Basic: 40 meas/sec ASCII format DOS compatible
Enhanced: 8 meas/sec
Extended: 1 meas/sec Program Storage: 125 per disk 25 setups internal
7600 Fast: 25 meas/sec Password protected ASCII format
Medium: 8 meas/sec
Calibration: Recommended Calibration Interval 1 year
Slow: 1 meas/sec
Complete NIST Traceable Calibration using
Ranging: Automatic, Range Hold or user selectable QuadTech 7000-09 Cal Kit
Built-in automatic calibration procedure
Trigger: Internal (automatic), External (RS-232,
IEEE-488.2 or Handler interfaces) and Manual Usage & Cal Data: Displays last calibration date, standard values
used in calibration and # of hours operation
AC Test Signal: Voltage: 20 mV to 5.0 V (open circuit)
up to 500kHz in 5 mV steps Self-Test Routine: Verifies critical instrument operation at power-
7600 20 mV to 1.0 V (open circuit) up or when selected from menu
500kHz-1MHz in 5 mV steps
Contact Check: Time to detect, 2ms
20 mV to 0.5 V (open circuit)
>1MHz in 5 mV steps Test Terminals: Front panel, four terminal (BNC) guarded
Current: 250 µA to 100 mA (short circuit) in Mechanical: Bench mount with tilt bail
50 µA steps Dimensions: (w x h x d): 16 x 6 x 14in
(Max. Compliance 3V < 500kHz. (410 x 150 x 360mm)
Weight: 17 lbs (8kg) net, 23 lbs (10.5kg)
Source Impedance: 25, 400, 6.4k, or 100k, range dependent
shipping
DC Bias Voltage: Internal: 2.0 V
Environmental: Meets MIL-T-28800E, Type 3, Class 5,
External: 0 to +/-200V
Style E & F
0 to +/-500V on 7400A/7600A
Operating: 0 to + 50° C
Display: LCD Graphics with back light and adjustable Humidity: <75% for 11 to 30° operating
contrast Storage: - 40 to + 71° C
Power: · 90 - 250Vac · 47/63Hz
· 100W max
Ordering Information
7400/7600 Precision LCR Meters 7400C LCR Meter, Charged Capacitor 7000-01 BNC Cable Set, 1 meter
7600 LCR Meter Protection 7000-02 BNC Cable Set, 2 meters
7600-CE LCR Meter, CE Marked 7400C-CE LCR Meter, Charged Capacitor 7000-03 Kelvin Clip Leads
7600A LCR Meter, +/-500V External Bias Protection, CE Marked 7000-04 Alligator Clip Leads
7600A-CE LCR Meter, +/-500V External Bias, Includes: 7000-05 Chip Component Tweezers
CE Marked Instruction Manual 7000-06 Axial/Radial Lead Component
7400 LCR Meter Power Cord Test Fixture
7400-CE LCR Meter, CE Marked Calibration Certificate Traceable to NIST 7000-07 Chip Component Test Fixture
7400A LCR Meter, +/-500V External Bias Optional Accessories: 7000-08 High Voltage Test Fixture
7400A-CE LCR Meter, +/-500V External Bias, 7000-00 Rack Mount Kit 7000-09 Calibration Kit
CE Marked
CompuMess Elektronik GmbH · Lise-Meitner-Str.1 · 85716 Unterschleissheim
Tel 089-321501-0 · Fax 089-321501-11 · www.compumess.de · www.netzteile.de
PN030087/A1
1855 Leakage Current/IR Meter
Capacitor Leakage Testing
USES:
· Production Testing of Leakage Introduction
Current on Electrolytic Capacitors, The 1855 Capacitor Leakage Current/IR Meter is a fast and reliable digital
Zener diodes, Neon lamps, and other leakage current meter. Primarily used for electrolytic capacitor leakage cur-
Capacitive Components rent testing, and aluminum-foil withstand voltage testing, the 1855 instrument
· Production Testing of Insulation also measures insulation resistance. The 1855 instrument comes standard with
Resistance on Switches, Connectors, an RS-232 interface plus it has an optional IEEE-488 & Handler interface for
and Other Devices high speed automated measurements. Whether its component evaluation on
· Testing Insulation Breakdown in the production line or bench-top testing in R&D applications, the 1855
accordance with EIAJ RC-2364A Capacitor Leakage Current/IR Meter is right for the task.
· Component Evaluation, Testing, and Description
Design
Leakage Current: The 1855 instrument measures and displays the undesir-
FEATURES: able flow of current through a capacitor or over any surface of insulation. The
leakage current function provides a measurement range from 1nA to 20mA and
· 0.3% Basic Measurement Accuracy
programmable test voltage from 1- 650V DC.
· Constant Current: 0.5mA ± 0.05mA Powerful Charge Current: The 1855 Model offers flexibility with program-
meets EIAJ RC-2364A WV test mable charge current from 0.5mA to 500mA in increments of 0.5mA.
· Programmable DC Voltage: 1-650V Programmable Source Voltage: The DC voltage can be programmed from
· Programmable Charge Current: 0.5- 1.0V to 100V in 0.1V increments (with current to 500mA) and from 101V to
500mA 650V in 1V increments (with current to 150mA).
· Programmable Charge & Dwell Precision Measurement: With a basic accuracy of 0.3%, the compact 1855
Times: 0-999 seconds unit makes consistent, stable, and reliable test results.
· Leakage Current Measurement from: Insulation Resistance: Serves as an economical megohmmeter by measuring
1nA - 20.00mA and displaying a product's insulation resistance. This resistance can be meas-
· Insulation Resistance Measurement ured over the range of 10 to 99G with a programmable test voltage from
from 10 - 99G 1.0V - 650V DC.
· Auto Ranging Aluminum-Foil Withstand Voltage: The 1855 meets the requirements of the
EIAJ RC-2364A standard with a low programmable constant current for
· Speeds Up to 18 Measurements/second charging aluminum electrolytic capacitors. The rise time (Tr) and final test
· Measurement Averaging (1-8) voltage (Vf) are shown on the instrument display.
· Standard RS-232 Interface 65 Watt Discharge Circuit: For operator safety and for rapid, complete dis-
· Optional IEEE & Handler Interface charge of large capacitors, a power discharge circuit is built into the 1855 unit.
· Front Panel Lockout
· Comparator and Pass/Fail Function
· Enhanced LCD Display
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
1855 Leakage Current/IR Meter
Leakage Current Test Measurement Mode: Continuous or Trigger (INT, EXT, MAN)
Measurement Range: 0.001uA - 20.0mA Ranging: Automatic or Hold
Accuracy: ± (0.3% + 0.005uA) Measurement Rate: Fast 18 Measurements/second
Medium: 14 Measurements/second
Test Voltage: 1.0V - 650V DC, 0.1V/Step Slow: 7 Measurements/second
Voltage Accuracy: ± (0.5% + 0.2V) Averaging: 1-8
Test Current: 0.5mA - 500mA, 0.5mA/Step DC <100V Compare: Upper & Lower Limits for LC & IR Tests
0.5mA - 150mA, 0.5mA/Step DC >100V Indication: Audible Alarm, Programmable High, Low
Charge Current or Off for Pass or Fail
Accuracy: ±(3% + 0.05mA) Front Panel Lockout: Keypad Lock
Display: 240 x 64 LCD Graphic Display
Insulation Resistance Test
Standard Interfaces: RS-232
Measurement Range: 10 - 99.99G
Optional Interfaces: IEEE-488 & Handler
IR Accuracy: + 0.6% (voltage & load dependent)
Connectors: 1 BNC Terminal: Input
Test Voltage: 1.0V - 650V DC, 0.1V/Step 2 Banana Terminals: HV(+), HV(-)
Voltage Accuracy: ± (0.5% + 0.2V) 1 Banana Socket: Chassis Ground
Test Current: 0.5mA - 500mA, 0.5mA/step DC <100V Dimensions: (w x h x d): 12.5 x 4.0 x 13.5 inches
(317.2 x 101.5 x 342.6 mm)
0.5mA - 150mA, 0.5mA/Step DC >100V
Weight: 18lbs (8.2kg) net, 22lbs (10kg) shipping
Charge Current
Accuracy: ±(3% + 0.05mA) Environmental: Operation: 10°C to +40°C
Storage: -10°C to +50°C
WithStand Voltage Test Humidity: <90%
Pollution Degree 2
Rise Time (Tr): 0.05 - 120s
Installation Category I
Withstand Voltage (Vf): 1.0V - 650V DC, 0.1V/Step Power: 90-125V AC
Test Current: 0.5mA - 150mA, 0.5mA/Step 190-250V AC
50/60 Hz
Charge Current 400 W Maximum
Accuracy: ±(3% + 0.05mA)
Measure Time: 30 - 600s
MAX Charge Time: 5 - 600s
General Features
Test Types: Automatic Sequence Test
Manual Step Test
Null: Correction for Lead Leakage
Monitor Voltage (Vm): Monitor & Display Voltage across DUT
Charge Time: 0 - 999seconds
Dwell Time: 0.2 - 990seconds
Discharge: 65 Watt Discharge Circuit
Trigger: Delay: 0 - 9.995seconds
Edge: Falling or Rising
Ordering Information
1855 Capacitor Leakage Current/IR Meter Optional Accessories:
QT P/N Description
Includes:
N/A Before & After Calibration Data
QT P/N Description
700171 IEEE-488/Handler Interface
150767 Instruction Manual
630157 RS-232 Cable
1855-01 Test Leads: Banana to Alligator Clip & BNC to Alligator Clip
4200-0300-00 AC Power Cable
520149 Power Line Fuse 115V Operation: T4A 250V
520148 Power Line Fuse 230V Operation: T2A 250V
N/A Calibration Certificate traceable to NIST
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
Series 1865 Megohmmeter/IR Tester
USES: High Resistance Meter
· Production Testing of Insulation on Introduction
Switches, Connectors, Cables, The 1865 Megohmmeter/IR tester, with digital display, is used for high accuracy measurements
Printed Circuit Boards, of insulation resistance on a wide variety of components, materials and electronic devices.
Resistance values greater than 100 teraohms can be measured with a basic accuracy of 0.5% at
Transformers, Motors and other
DC voltages up to 1000V. A programmable limit makes the unit ideal for pass/fail testing in a
Devices production environment and is also adaptable for use in automated system applications with its
· Insulation Properties of Natural and optional IEEE-488 interface.
Synthetic Materials such as Oils, Description
Plastics, Rubber or Porcelains Precision Measurements: The 1865 provides resistance measurement capability over a range of
1k to 100T (test voltage dependent), with a basic accuracy of 0.5%. To meet the test
· Screening and Sorting of High requirements for a wide range of devices, the test voltage is fully programmable up to 1000V
Resistance Components DC. Sensing the proper resistance measurement range is done automatically, thus eliminating
setup errors: and in order to eliminate lead or fixture errors, the operator can easily initiate an
· Incoming Inspection and Quality
automatic zeroing routine of test leads.
Assurance Testing
Easy To Use: The 1865's menu programming system, simple controls and indicators combine
· Product Design and Evaluation of
for efficiency of test and productivity. It's multi-function keypad provides the operator with an
Insulation Properties easy way to program and make measurements.
Pass/Fail: Measured results are automatically compared to an operator programmed limit for
FEATURES: pass/fail testing. Psss/Fail indicator lights or a pass/fail output from the instruments I/O inter-
· Measurement Range to 100T face give a clear indication of the measurement results.
· Programmable Test Voltage from 1 Program Data Storage: Test setup conditions and measured results can be stored in instrument
to 1000 V DC memory or on 3 1/2" disk when using the extended program storage option.
· 0.5% Measurement Accuracy Automated Testing: For automated system applications, the instrument includes an I/O inter-
face connection with remote start and pass/fail outputs. An optional IEEE-488 interface is also
· Automatic Ranging available (or added later) which enables the 1865 to be used under computer control.
· Programmable Test Times
Current Display Mode: Besides a readout of insulation resistance in ohms, the operator can
· High Resolution LCD Display select a display mode for reading the measured current directly.
· Storage of Test Setup and Results Safety Features: The 1865 provides safety features such as current limiting, a warning indicator
· Automatic Zeroing of Test Leads when high voltage is active, and safety interlock, all for protection of the operator.
· Limit Entry for Pass/Fail Testing Component Test Fixture: An accessory fixture is available for use with the 1865 which acco-
modates a variety of component types, including radial, axial, and chip components. Its shield-
· Direct Reading of Measured Current ed case reduces electrical noise and interfernce and includes a cover interlock switch and remote
· Keypad Lockout with Password start for maximum operator safety.
Protection
For more detailed specifications,
· RS-232 and I/O Interfaces visit
· Optional IEEE-488 Interface www.quadtech.com
For more information about special
purchase, rent & lease options, call
1-800-253-1230
Fax 1-978-461-4295
Intl. 1-978-461-2100
CompuMess Elektronik GmbH, Lise-Meitner-Str. MEGOHMMETERS · MILLIOHMMETERS
HIPOT · LCR METERS ·
1, 85716 Unterschleißheim
Tel.: (089) 321 501-0; Fax: (089) 321 501-11; eMail: info@compumess.de; www.compumess.de; www.netzteile.de
1865 Megohmmeter Dimensions: Benchtop unit with tilt back bail
(w x h x d) :(17.5 x 5.25 x 16in)
Resistance Range: 7 ranges (automatic or manual)
Product Specifications
(444.5 x 133.4 x 406.4mm)
1 x 103 to >1 x 1014 (voltage dependent)
1 x 106 to >1 x 1014 at 1000V DC Weight: 18 lbs (8.2kg) - Net
1 x 105 to 1 x 1013 at 100V DC 26 lbs (11.8kg) - Shipping
1 x104 to 1 x 1012 at 10V DC
1x 103 to 1x 1011 at 1V DC Power: 90 to 250V,
47 or 63 Hz
Resistance 60W max
Accuracy: ± [0.45% + {(Rx/Vx)(0.0005 FS + 2pA) +
30 /Rx}100%] Environmental: In accordance with MIL-T-28800D,
Rx: Measured resistance in ohms Type 3, Class 5, Syle E & F
Vx: Programmed voltage in volts Operating: 0°C to +50°C,
FS: Full scale current range in amperes Storage: -40°C to +70°C
Voltage Range: 1 to 1000 volts programmable in two ranges
Voltage Accuracy: 1 - 100V: 1% of setting + 1V, 25mV resolution
100 - l000V: 1% of setting + 2V, 250mV
resolution
Output Voltage
Impedance: 1k, ± 5%
Current Limited: < 2mA
Current Measure: 1 x10-13 - 1 x 10-3A
Current* Accuracy: 1nA- 1mA ± [0.5% + (0.0005FS + 2 pA)]
100pA- 1nA ±[1% + (0.0005FS + 2pA)]
1pA - 100pA ± [10% + (0.0005FS + 2 pA)]
*Specified at front panel connectors 1865-51 Shielded Lead Set (optional accessory)
Input Impedance: 5k, ± 5%
Measure Limits: Pass/Fail (1 limit)
Display: · LCD graphics display
· Voltage warning indicator
· Pass/Fail indicator
Test Cycle: Manual: Charge, Measure, Discharge
Automatic:
Charge: (0 - 300 sec), Measure: (0 - 999 sec)
Dwell: (0 - 300 sec), Discharge: (0 - 300 sec)
Interfaces: Standard: RS-232,I/O Port (w/safety interlock)
Optional: IEEE-488 & Data/ Program Storage 1865-52 Component Test Fixture (optional accessory)
31/2:" disk
1865-52 Component Test Fixture
Input Terminals: Four sheathed banana jacks, front or rear
Components Leaded Module: Body Size < 1inch
(optional) mount
Accomodated: Lead Size < 1.4mm dia
· + unknown (red) · guard (blue)
SMD Module: Width: 0.5 to 10mm
· - unknown (black) · ground (green)
Height: 0.5 to 10mm
Other Features: · Menu Programming · Stop on Pass (Diameter 0.5 to 3.0mm)
· Automatic Zeroing · Safety Interlock Length: 0.1 to 8mm
· Stored Test Conditions · Keypad Lockout Alligator Clips: < 5mm diameter
· Measurement units (engineering or scientific) Dimensions: (w x h x d): (8 x 5.5 x 9in), (203 x 140 x 230mm)
· Measurement averaging (1 - 400) Weight: 5 lbs (2.3kg) - Net, 9 lbs (4kg) - Shipping
Ordering Information
1865-00 Megohmmeter/IR Tester Optional Accessories:
Includes: 1865-01 IEEE Interface Option (factory installed)
1865-02 Data/Extended Program Storage Option (factory installed)
150073 Instruction Manual
1865-03 Rear Panel Input Option (factory installed)
XX Calibration Certificate Traceable to NIST
1865-50 Rack Mount Kit
700070 AC Power Cable
1865-51 Shielded Lead Set
800014 100k Capacitor Adaptor
1865-52 Component Test Fixture
800015 1M Capacitor Adaptor
1865-70 IEEE Interface Option (field retrofit)
520049 Spare T2.5A, 250V Power Line Fuse
Calibration Data
For more detailed specifications, visit www.quadtech.com
For more information about special purchase, rent & lease options, call
1-800-253-1230 · Fax 1-978-461-4295 · Intl. 1-978-461-2100
5 Clock Tower Place, 210 East, Maynard MA 01754 P/N 030047/A4
CompuMess Elektronik GmbH, Lise-Meitner-Str. 1, 85716 Unterschleißheim
Tel.: (089) 321 501-0; Fax: (089) 321 501-11; eMail: info@compumess.de; www.compumess.de; www.netzteile.de
1868 Series 1868A-D Megohmmeters
USES: High Resistance Testing To 1P
· Production Testing of Insulation on
Switches, Cables, Transformers, Motors and Introduction
Other Devices The 1868 Megohmmeters (Models A&D) are precise, full-featured digital instruments
· Testing of Capacitive Components with both resistance and current measurement modes. They are capable of measuring
Insulation Resistance from 10k to 1P at programmable DC test voltages between 10
· Insulation Properties of Natural and
and 1000V (1868A) or 50 and 5000V (1868D). For charging high capacitive devices,
Synthetic Materials such as Oils, Plastics,
the 1868A supplies a powerful charge current up to 80mA and the 1868D up to 18mA.
Rubber or Porcelains
Remote I/O, RS232 and IEEE-488.2 interfaces for remote control operation and com-
· High Resistance Testing of Electrical munication with other instrumentation are standard on both models.
Connections
Description
FEATURES: Wide Measurement Ranges: Measure resistance from 10k to 1P with basic accu-
racy of +2% up to 1T. Measure Leakage Current down to 1pA with basic accuracy
· Measurement Range: 10k to 1P of +2%.
· Basic Accuracy: ± 2% to 1T Programmable Test Voltage: From 10V to 1kV in 1V increments on the 1868A
· Programmable Test Voltage: 10V to 1kV Model, and from 50V to 5kV in 1V increments and on the 1868D Model.
(1868A), 50V to 5kV (1868D) Powerful Charge Capability: The 1868A Model offers current ranges of
· Selectable Charge Current: to 80mA 2mA/25mA/80mA and the 1868D offers current ranges of 2mA/10mA/18mA.
(1868A), to 18mA (1868D) Currents above 2mA are password protected for safety.
· Leakage Current Measurement Down to Programmable Charge, Delay & Discharge Times: Allows testing of highly capac-
1pA (± 2% Basic Accuracy) itive devices without false failures.
· Programmable Charge, Delay and Standard Interfaces: The 1868 models come standard with RS232 and GPIB inter-
Discharge Times faces for PC connection in automated applications. Incorporate the 1868 unit into an
automated manufacturing environment with remote start and bin results output
· 5 Programmable Limit Sets
through the rear panel PLC interface.
· Internal Storage of 4 Tests (20 Steps each)
Graphical Display: The backlit display enables quick, easy setup and display of the
Plus Additional Storage with Optional
test results as text, bar graph or X-Y graph. The X-Y Graph is an excellent tool to view
PCMCIA Memory Card
current or resistance measurements over time.
· Standard RS232, IEEE and Remote I/O Test Storage: Store 2 Global Setups including instrument setup and sequence setups,
Interfaces 4 user-programmable test sequences (up to 20 steps each), and 4 pre-programmed test
· Graphic LCD with Text, Bar Graph and sequences internally. The PCMCIA interface increases test setup storage with the
X-Y Graph Displays capability of uploading/downloading test setups to a memory card.
· Current or Resistance Display Mode
· 4 Ranges Plus Automatic Ranging
· Automatic Zeroing
· Contact Check Function
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
· Floating Power Supply (1868A) for Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
Measurements on Grounded Devices
HIPOT · LCR METERS · MEGOHMMETERS · MILLIOHMMETERS
1868A-D Megohmmeter
Resistance Range: 10k - 1P (dependent on test voltage) Display: LCD graphic display
4 Ranges or Auto Range: 3.5 digit resolution
Range 1: 1pA to 10nA Bar Graph: 8 ranges/2 decades/graph,
Range 2: 2nA to 100nA Fixed or auto-scale
Range 3: 20nA to 10uA Line Graph: X-Y: I or R versus Time
Range 4: 2uA to 1mA Indicators: HV, Measure, Bin, Remote
Resistance Accuracy: For Rx <20G (Vx): ±(2% of reading +5cnt) Standard Interfaces: RS232, IEEE 488, Remote I/O
For Rx >20G (Vx): ±(Vx/1pA) in ohms. Internal Storage: 2 Global Setups (Save Instrument Setup
Max reading: Vx/0.1pA and Sequence Setups)
Rx = Measured resistance in ohms 4 User-Programmable Sequence Setups,
Vx = Programmed voltage in volts (Up to 20 Steps each)
Voltage Range: 10 to 1000V DC in 1V steps, 1868A 4 Pre-Programmed Sequence Setups
50 to 5000V DC in 1V steps, 1868D External Storage: PCMCIA Interface for 2M SRAM Memory
Voltage Accuracy: 2% of setting Cards (20 Setups/20 Steps each)
±1V in uncalibrated mode Input Terminals: HV: BNC Connector
Source Resistance: 100, 1kV (1868A); 3.3k, 5kV (1868D) I IN: Triaxial Connector
GUARD: Sheathed Banana Plug
Charge Current: 2/25/80mA (1868A); 2/10/18mA (1868D)
Safety: Interlock Plug
Discharge Resistance: 100k
Password-protected Charge Current
Current Measure: 1pA to 1mA (For I > 2mA)
Current Accuracy: ±[2% of reading +5cnts +1pA] HV Break Red LED/Push Button
Input Impedance: For Ix > 10nA: 10k ; For Ix < 10nA: 1M Dimensions: (w x h x d):12.5 x 4.5 x 15.5 inches
Ix = Programmed current in amperes (312.5 x 112.5 x 387.5 mm)
Measure Limits: 5 Programmable Limit Sets Weight: 28 lbs (12.7kg) net
Measurement Result: Resistance or Current 41 lbs (18.6kg) ship
Measurement Mode: Continuous or Triggered Environmental: Operating: 10°C to +40°C, 80% RH
Averaging: 1-100 measurements Power: 110V - 240V
50 or 60Hz
Test Speed: Trigger Mode: 40msec
400W Max (1.8A at 220V AC,
Continuous Mode: 90-4000msec 3.2A at 125V AC)
(Depending on # to Average)
Programmed Time: Charge: 0 - 9999msec (Charge R: 200)
Measurement Delay: 0 - 9999msec
Discharge: 0 - 100sec or Auto mode
Auto: 0.1(Cx) as Vx goes to 1% Vt
Cx = Measured capacitance (µF)
Vx = Programmed voltage (V)
Zero/Offset: Automatic Zeroing of All Ranges or
Individual Zeroing of 4 Ranges
Ordering Information
1868A Megohmmeter: 2/25/80mA, 1kV Optional Accessories:
1868D Megohmmeter: 2/10/18mA, 5kV Calibration Data
2100-04 2MEG SRAM PCMCIA Memory Cards
Includes:
150753 Instruction Manual
700070 Power Cable
1868-01 1868A Alligator Clip Lead Set (1868A only)
1868-02 19" Rack Mount Brackets (Set of 2)
1868-03 1868D Alligator Clip Lead Set (1868D only)
1868-04 Interlock Plug
N/A Calibration Certificate Traceable to NIST
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
LR Series LR2000 Milliohmmeter
A Precision Low Resistance Meter
USES:
Introduction
· Production Testing of Contact Resistance
The QuadTech LR2000 Milliohmmeter with its LCD display and menu type
of Switches, Relays, Connectors, Cables,
front panel programming assures that low resistance measurements on switch-
and Other Low Resistance Devices
es, relays, connectors, cables, and other devices can be made quick and easy.
· Testing of Low Value Resistors, Fuses, With a basic accuracy of 0.05% the instrument offers a wide measurement
Squibs, and Heating Elements range from 1µohm to 2Mohms. For remote operation and production appli-
cations the unit comes standard with an RS-232 interface, plus IEEE-488 and
· Winding Resistance of Motors,
handler interfaces are available as options. For measurement integrity, contact
Transformers, Solenoids, and Ballasts
to the test device is made via a 4-terminal Kelvin connection that incorporates
· Conductivity Evaluation in Product an automatic zeroing function to compensate for lead errors.
Design Description
· Incoming Inspection and Quality Wide Measurement Range: Eight measurement ranges from 20m to 2M
Assurance Testing with constant current between 1A and 1µA. For "dry" contact measurements
(those contacts whose resistance can be altered by excessive voltage potential)
FEATURES: the LR2000 can be limited to 20mV on selected measurement ranges.
Test Signal: Besides the standard DC test signal, the LR2000 provides a signal
· 1µ - 2M Measurement Range
reversal mode for eliminating thermal EMF's, and pulsed current mode for
· 1µA - 1A Constant Current minimizing errors caused by device heating.
· 0.05% Basic Measurement Accuracy Precision Measurements: With a basic measurement accuracy of 0.05% the
instrument makes for consistent, reliable test results.
· Measurement Speed to 15/second
Graphical Display: 240 x 64 dot matrix graphical LCD display for user friend-
· Graphical LCD Display ly menu programming and display of measured results.
· Four Terminal Kelvin Connection Measurement Rate: Three measure modes of 15, 6 and 1.5 measurements per
· Automatic Zeroing second with varying degrees of accuracy.
· RS-232 Interface Standard Pass/Fail Testing: Provides a programmable Hi/Lo comparator function in
absolute value or %, as well as 8 sorting bins for categorization of components.
· IEEE and Handler Interfaces, Optional
Zeroing: An automatic zeroing functions reduces the effects of lead resistance
· Automatic Hi/Lo Comparator Limits through the front panel 4-terminal Kelvin connection.
· Pass/Fail Sorting (8 Bins) Interfaces: For remote control, or adaptation to a production type environ-
· Voltage Limiting for Dry Contact Testing ment, the LR2000 includes an RS-232 interface standard. An IEEE-488 and
Handler interface are available as an option.
· Keypad Lockout
· Programmable Delay Times
CompuMess Elektronik GmbH
Lise-Meitner-Str.1, 85716 Unterschleissheim
Tel 089-321501-0 Fax 089-321501-11
http://www.compumess.de oder http://www.netzteile.de
HIPOT · LCR METERS · MEGOHMMETERS · MILLIOHMMETERS
LR2000 Milliohmmeter Features
Resistance Range:
Range F.S. Resolution Accuracy Test I (Typical)
20m 1µ ±(0.1% of rdg + .006m) 1A
200m 10µ ±(0.05% of rdg + .06m) 100mA
2 100µ ±(0.05% of rdg + .6m) 10mA
20 1m ±(0.05% of rdg + 6m) 1mA
200 10m ±(0.05% of rdg + 40m) 1mA
2k 100m ±(0.05% of rdg + .2) 1mA
20k 1 ±(0.1% of rdg + 2) 100µA
200k 10 ±(0.2% of rdg + 20) 10µA
2M 100 ±(0.4% of rdg + 200) 1µA
Test Signal: Modes: DC+, DC-, Pulse+, Pulse-, Dimensions: (w x h x d): 12.5 x 4.0 x 13.5in
Pulse+/- and STBY (312.5 x 100.0 x 337.5mm)
Dry Circuit: Open Circuit Voltage <20mV Weight: 10.85 lbs. (5kg) net, 15.2 lbs. (7kg) ship
for 200m, 2 and 20 ranges
Measurement Rate: Fast: 15 measurements/second Environmental: Specifications: +15°C to +35°C, 75% RH
Medium: 6 measurements/second Operating: 10°C to +40°C
Slow: 1.5 measurements/second Storage: 0°C to +50°C
Humidity: 10 - 90% RH
Measurement Mode: Continuous or Trigger Pollution Degree 2
Trigger: Internal Installation Category II
Manual Power: · 90 - 125V AC
External (IEEE or Handler) · 190 - 250V AC
Delay Times: Trigger Delay: 5 - 1000ms · 48 - 62 Hz
Measurement Delay: 0 - 100s · 80W max
Ranging: Automatic or Hold Range
Zeroing: Open and short circuit compensation
Averaging: 1 - 10
Comparator: Hi/Lo Limits (Value or %)
Binning: Hi/Lo Limuts (8 bins in %)
Indication: Audible Alarm programmable: HI LO or
OFF for Pass or Fail Result
Display: 240 by 64 dot matrix LCD display
Setup Storage: Auto recall on power-up
Lock: Keypad Lockout
Interfaces (Standard): RS-232
Interfaces (Optional): IEEE-488 and Handler
Test Terminals: Front: 4 Sheathed Banana & 1 GND
Ordering Information
LR2000 Milliohmmeter Optional Accessories:
B/A Calibration Data
Includes:
LR2000-50 Kelvin Clip Lead Set
QuadTech P/N Item
700171 IEEE-488/Handler Interface
150713 LR2000 Instruction Manual
LR2000-50 Lead Set: 4 Banana Connectors to 2 Kelvin Clips
4200-0300 AC Power Cord
520026/520138 Power Line Fuses (1.0A 250V/0.5A 250V)
Calibration Certificate Traceable to NIST
CompuMess Elektronik GmbH
For more detailed specifications, visit www.quadtech.com
For more information about special purchase, rent & lease options, call
Lise-Meitner-Str.1, 85716 Unterschleissheim
1-800-253-1230 · Fax 1-978-461-4295 · Intl. 1-978-461-2100
5 Clock Tower Place, 210 East, Maynard MA 01754
Tel 089-321501-0 Fax 089-321501-11 P/N 030127/A1
http://www.compumess.de oder http://www.netzteile.de