MPA150 Series
Compact 1U 150W
Single Output
Power Factor Corrected Only
5 x 3.2 x
AC/DC Power Supplies 1.5 in!!
Key Features: Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
j g
· Compact 1U 150W Supply
Input
· PFC to EN61000-3-2 "A" Parameter Conditions Min. Typ. Max. Units
· UL, cUL, TUV Approvals 90 132
· CE Certified Input Voltage Range Autoranging VAC
180 264
· FCC Class B Emissions Input Frequency 47 63 Hz
· 3 - 56 V Output Voltages 110 - 120 VAC 4
Input Current, Full Load A
· Auto Selectable AC Input 200 - 240 VAC 2
· 600W Peak Power 110 VAC 35
Inrush Current, Cold Start A
· Four Mechanical Options 220 VAC 70
Leakage Current 240 VAC 1.5 mA
Power Factor Correction Meets EN61000-3-2 Class A
Input Protection T4A/250V Fuse
Output
Parameter Conditions Typ. Min.
Max. Units
Output Voltage Adjustment By Trim Pot ±5.0 %
Output Regulation (Note 1) ±1.0 %
Hold Time 110 VAC, 80% Load 20 mSec
Ripple & Noise (20 MHz) (Note 2) See Model Selection Guide
Overload Protection Foldback with Autorecovery 110 140 %
Over Voltage Protection >130% of Rated Output Voltage. Recycle AC Input.
Over Temperature Protection >+85ºC Ambient with Autorecovery
Temperature Coefficient ±0.04 %/ºC
Transient Recovery Time (Note 3) 2.5 mS
50% Load Change
Transient Response Deviation 5 %
Overshoot/Undershoot At Turn On/Off ±5.0 %
Turn On Delay 120 VAC 1 S
Output Short Circuit Continuous With Autorecovery
General
Parameter Conditions Min. Typ. Max. Units
Input - Output 3,000
Isolation Voltage (Note 4) Input - FG (Frame Ground) 1,500 VAC
Primary - Core 1,500
Switching Frequency Fixed 25 kHz
MicroPower Direct Interface Signals
292 Page Street
Power Supply On Green LED (LED1) on the PCB
Suite D
PG on CN1. Goes TTL high 100 to 500 mS after regulation. Goes low at
Stoughton, MA 02072 Power Good Signal
least 1 mS before the loss of regulation. Will sink 100 mA.
USA
Remote On/Off RMSW on CN1. A TTL low signal inhibits the output. Hiccup Mode
T: (781) 344-8226 Environmental
F: (781) 344-8481 Parameter Conditions Min. Typ. Max. Units
E: sales@micropowerdirect.com Operating Temperature Range Ambient 0 +25 +50 ºC
W: www.micropowerdirect.com Output Derating 2.5%/ ºC from +50 ºC to + 70 ºC
Storage Temperature Range -20 +85 ºC
Cooling See Model Selection Guide
Operating Humidity RH, Non-condensing 90 %
Reliability Specifications
Parameter Conditions Min. Typ. Max. Units
MTBF MIL HDBK 217F, 30ºC, Gnd Benign 100 kHours
Safety Standards UL 60950; CSA C22.2 No. 60950; TUV EN60950; CB Report (IEC 60950)
EEMI Compliance Compliance to EN55022 (CISPR22) Class B; EN61000-3-2,3
EMS Immunity Compliance EN6100-4-2,3,4,5,6,8,11; EN55024,; CE Marked (LVD)
CompuMess Elektronik GmbH · Lise-Meitner-Str. 1 · D-85716 Unterschleißheim
Telefon (089) 32 15 01 - 0 · Telefax (089) 32 15 01 - 11
info@compumess.de · www.compumess.de · www.netzteile.de
Model Selection Guide
Output Voltage Max. Output Current (Note 5,6,7) Input Connector CN3:
Model Ripple & Efficiency Mating Molex Part No. 09-91-0500 (5 pin, 3 used) or Howder
Factory 16 CFM Convection Min. Terminal Block No. HD-603-3P (3-pin) or equivalent.
Number Range Noise (Note 7)
PreSet (U/w Air, E, F) (U) Output Connector CN2:
MPA150x-Az 3.3 VDC 3.0 - 4.0 VDC 30.00A 20.00A 0.0A 50 mV p-p 70% Mating Molex Part No. 09-91-0600 (6 pin) or Howder Terminal
Block No. HD-601-4P (4-pin) or equivalent.
MPA150x-Bz 5 VDC 5.0 - 6.0 VDC 30.00A 20.00A 0.0A 50 mV p-p 75%
Output Pin Assignment:
MPA150x-Cz 12 VDC 12.0 - 16.0 VDC 12.50A 8.33A 0.0A ±1% p-p 80%
Howder Molex
MPA150x-Dz 18 VDC 17.0 - 23.0 VDC 8.33A 5.55A 0.0A ±1% p-p 83%
Pins 1 ~ 2: V+ Pins 1 ~ 3: V+
MPA150x-Ez 24 VDC 24.0 - 30.0 VDC 6.25A 4.16A 0.0A ±1% p-p 83%
Pins 3 ~ 4: V- Pins 4 ~ 6: V-
MPA150x-Fz 48 VDC 35.0 - 56.0 VDC 3.12A 2.08A 0.0A ±1% p-p 83%
Notes: 5. The full output range (see table above) is covered in the safety Logic Signal Connector CN1:
1. Output regulation includes line & load. agency certification. Standard models are factory set to the Mating JST XHP-3 or equivalent (CHYAO SHIUNN JS-2001-03).
2. Ripple & noise is measured from 10 Hz to 20 MHz. Measurement connection to the "Preset" voltage. This may be set to other levels within the range
unit is made with a 0.1 µF ceramic capacitor & a 22 µF electrolytic capacitor con- without affecting the agency certification. For more information, Fan driver connector (FAN):
nected in parallel. contact the factory. 12 VDC / 300 mA is available to drive an external fan. Mating JST
3. Transient recovery is measured to within a 1% error band for a load step change of 6. Units will provide peak power of 600W for 500 µS. For units XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02).
50% to 100%. capable of longer durations, contact the factory.
4. Isolation specifications are production HI-Pot tested for 3 seconds. 7. A 1% minimum load is required to maintain regulation and ripple
specifications.
Mechanical Dimensions: U-Chassis (U Suffix) U-Chassis Cover (A Suffix)
U-Chassis Cover/W Fan (F Suffix) U-Chassis Cover (B Suffix)
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 · TEL: (781) 344-8226
CompuMess · FAX: (781) 344-8481 · E-Mail: sales@micropowerdirect.com
Elektronik GmbH · Lise-Meitner-Str. 1 · D-85716 Unterschleißheim
Telefon (089) 32 15 01 - 0 · Telefax (089) 32 15 01 - 11
info@compumess.de · www.compumess.de · www.netzteile.de